Skip to content
ChainsawGo logo — chainsaw icon with the ChainsawGo wordmark
  • Home
  • About UsExpand
    • Contact Us
  • Cordless Chainsaws
  • Gas Chainsaws
  • Chainsaw Parts
  • Safety Gear
  • Chains & Bars
  • Free Tools
ChainsawGo logo — chainsaw icon with the ChainsawGo wordmark
Free calculator

Chainsaw Mill Bar Length & Max Log Width Calculator

Find the widest log your bar can mill after your mill's allowance, or the bar length you need for a given log, in inches or mm.

  • Free
  • No sign-up
  • Runs in your browser
Estimates only · data checked October 2026 · About this data

This calculator gives a size estimate only. Chainsaw milling is hazardous. Follow your mill and saw manufacturers' manuals and use appropriate protective equipment.

Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.

Quick answer

For an Alaskan-style chainsaw mill, you need a bar at least as long as your log’s largest diameter plus the length your mill’s brackets use up (the mill allowance). Enter your bar, allowance and log below to get the maximum cut width or the bar length you need.

How to use the mill bar length calculator

  1. Choose a mode. Max cut width for my bar tells you the widest log your current bar can mill. Bar needed for my log tells you the bar length a log requires.
  2. Pick inches or millimetres. If you switch units after typing, your values are converted for display, not cleared. The calculator keeps your exact entries, so switching units never changes the result, and switching back shows the numbers you typed.
  3. Enter the bar length (first mode only). Use the nominal length stamped on the bar, or the usable cutting length if that is what your mill’s spec uses.
  4. Enter the mill allowance from your mill manufacturer’s spec sheet or manual. If the spec only gives a usable cutting length, enter 0 and use that length as the bar length.
  5. Enter the log diameter. Measure the largest diameter along the section you plan to mill, not the small end.
  6. Press Calculate. If a value is missing or out of range, a hint tells you what to enter.
  7. Read the result. It includes a one-line answer you can copy, a fits/too-wide badge with text and an icon, and the spare or short-by margin. If the margin is smaller than the display rounding, it reads “less than 0.1 in” or “less than 1 mm” instead of zero.

How the calculation works

The tool uses one subtraction and one addition, with every figure coming from you. All maths runs in millimetres internally (1 in = 25.4 mm exactly), using the values exactly as you entered them. Only the displayed results are rounded: to one decimal in inches or to the whole millimetre. The fits/too-wide verdict always uses the unrounded numbers, so a log that is a fraction too wide is never shown as fitting.

  • Maximum cut width = bar length (B) − mill allowance (A). The log fits if its diameter (D) is no more than this width. The margin is the width minus the diameter: positive means spare, negative means short by.
  • Bar needed = log diameter (D) + mill allowance (A). The tool then finds the smallest bar size on our list that is at least that long.

The examples below use hypothetical inputs. They are examples, not recommendations, and the allowances are not taken from any real mill.

Example (hypothetical)InputsFormulaResult
Max cut widthB = 36 in, A = 4 in, D = 30 in36 − 432 in; log fits with 2 in spare
Exact fitB = 20 in, A = 2 in, D = 18 in20 − 218 in; fits with no clearance
Just too wideB = 20 in, A = 2 in, D = 18.02 in20 − 218 in; too wide by less than 0.1 in
Bar neededD = 16 in, A = 2 in16 + 218 in; nearest listed size 18 in
Bar needed, beyond listD = 30 in, A = 4 in30 + 434 in; larger than the sizes we list
Worked examples with hypothetical inputs. Your mill’s allowance will differ.

An exact fit means the log diameter equals the maximum cut width. That leaves no clearance at all, so treat it as a limit rather than a comfortable setup.

Finding your mill’s allowance

Generic bar-size charts assume the whole bar can cut. On a chainsaw mill, though, the clamps or brackets that hold the bar take up part of its length, near the saw and often at the nose too. Wood can only pass through the stretch of bar between them. That lost length is the allowance, and it is why a bar can be “big enough” on paper yet still too short for a log once it is in the mill.

Mills differ in how they mount the bar, so we do not suggest a default allowance for any brand. Look in your mill’s manual or spec sheet for one of two things:

  • An allowance or “bar length lost” figure. Enter it as the mill allowance, with your nominal bar length.
  • A maximum log width or usable cutting length for a given bar. Enter 0 as the allowance and that usable length as the bar length.

Also check which bar figure the spec means. Husqvarna’s manual notes that “the nominal guide bar size is not necessarily the same as the cutting length”, and STIHL’s says “the actual cutting length may be less than the specified cutting length.” Use the same kind of length your mill’s spec is based on. Bar ranges vary by saw, too. For example, Husqvarna lists 15, 16, 18, 20 and 24 in bars for the 455/460, and 13–20 in for the 445/450. Check that your saw is rated for the bar the calculator points to.

Methodology & sources

Every number the calculator shows is computed from your inputs using the two formulas above. Unit switching only changes how values are displayed; the calculator stores each value exactly as you typed it, in the unit you typed it in, so a fit or no-fit verdict cannot flip just because you changed units. The “nearest listed bar size” comes from the distinct bar lengths in the chainsaw bar listings on this site (10, 14, 16, 18, 20, 24 and 28 in, snapshot September 2026). If the bar you need is longer than 28 in, the tool says so rather than guessing a size. No external statistics, prices or engine-power requirements are used. Input limits of 1–120 in (25–3050 mm) are sanity checks only, not recommendations. The calculator gives a size estimate only; it is not a manufacturer specification and does not say that any bar will safely mill a given log.

  • Your mill manufacturer’s spec sheet or manual: the mill allowance (supplied by you).
  • Husqvarna operator’s manual: nominal guide bar size vs cutting length.
  • STIHL instruction manual: actual vs specified cutting length.
  • Husqvarna 455/460 operator’s manual: bar lengths 15–24 in.
  • Husqvarna 445/450 operator’s manual: bar lengths 13–20 in.
  • Inch (Wikipedia): 1 in = 25.4 mm exactly.

Last updated: October 2026

Safety: This calculator gives a size estimate only. Chainsaw milling is hazardous. Follow your mill and saw manufacturers’ manuals and use appropriate protective equipment.

FAQ

What size chainsaw bar do I need for an Alaskan mill?

You need a bar at least as long as the log diameter plus your mill’s allowance (neededBar = D + A). Take the allowance from your mill’s manual, enter it with the largest log diameter, and the calculator gives the bar length and the nearest size we list.

What is the mill allowance?

It is the length of bar that the mill’s brackets, clamps and mounting use up, so it cannot cut wood. Read it from your mill manufacturer’s spec sheet or manual. If the spec gives a usable cutting length instead, enter 0 and use that length as the bar length.

How wide a log can my bar mill?

The maximum cut width is the bar length minus the mill allowance (maxWidth = B − A). A log fits if its largest diameter along the section is no more than that width.

Is the nominal bar length the same as the cutting length?

Not necessarily. Husqvarna notes that the nominal guide bar size is not necessarily the same as the cutting length, and STIHL says the actual cutting length may be less than specified. Use whichever figure your mill’s spec is based on.

Does the calculator tell me how powerful my saw must be?

No. It only works out lengths from the numbers you enter. For engine size and safe use, follow your mill and saw manufacturers’ manuals.

Related guides

  • What Size Chainsaw for an Alaskan Mill? CC and Bar Length Reference
  • Types of Chainsaw Chains: Full Chisel, Semi-Chisel, Low-Profile and Ripping
  • Chainsaw Chain Size Chart by Bar Length, Pitch and Saw Model
  • Are Battery Chainsaws as Powerful as Gas? Cutting Speed and Torque Compared
  • How to Measure a Chainsaw Chain: Pitch, Gauge and Drive Links
  • How Often to Replace a Chainsaw Chain? Signs It’s Worn Out

More free tools

Battery Chainsaw Runtime Estimator

Estimate battery chainsaw runtime from battery voltage, amp-hours, rated watts and duty cycle, with an optional corded-saw energy comparison.

Battery vs Gas Chainsaw Cost-of-Ownership Calculator

Compare the total cost of a gas and a battery chainsaw over the years with your own fuel, power and usage numbers, and find the break-even point.

Chainsaw Bar, Chain & Sprocket Fitment Chart

Look up bar lengths, chain pitch, gauge, drive links and sprocket for listed Husqvarna and STIHL saws, or find saws by pitch and gauge.

See all free tools (9) →

  • Home
  • About Us
  • Contact Us
  • HTML SITEMAP
  • Privacy Policy
  • Terms of Service
  • Affiliate Disclaimer
  • How We Research

Please keep in mind that we may receive commissions when you click our links and make purchases. However, this does not sway our reviews and comparisons. We try our best to keep things unbiased, in order to help you make the best choice. As Amazon Associate, we earn from qualifying purchases.

© 2026 ChainsawGo | All Rights Reserved.

Scroll to top
  • Home
  • About Us
    • Contact Us
  • Cordless Chainsaws
  • Gas Chainsaws
  • Chainsaw Parts
  • Safety Gear
  • Chains & Bars
  • Free Tools
Search