Chainsaw Bar, Chain & Sprocket Fitment Chart
Look up bar lengths, chain pitch, gauge, drive links and sprocket for listed Husqvarna and STIHL saws, or find saws by pitch and gauge.
- Free
- No sign-up
- Runs in your browser
Estimates only · data checked October 2026 · About this data
Reference only: specs are taken from manufacturer operator's manuals (checked October 2026). Always confirm pitch, gauge and drive-link count against the stamp on your bar and your owner's manual before buying; a mismatched chain, bar or sprocket can damage the saw and is unsafe.
Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.
Quick answer
A chainsaw bar cross reference chart tells you which bar length, chain pitch, gauge, drive-link count and sprocket fit your saw. Pick your model below, or enter a pitch and gauge to see which listed saws use it. Every spec comes from the manufacturer’s manual, so you can confirm it against your bar stamp before buying.
How to use the fitment chart
- Look up by “My saw”: choose the brand and model. Leave the bar length empty to see every bar the manual lists, or enter the nominal length (in inches) to get the pitch, gauge, drive links and sprocket for that one bar. If the manual does not list that length for your saw, the result box says so.
- Look up by “Chain specs”: pick the pitch and gauge stamped on your bar. Add a bar length and drive-link count if you know them. The chart warns you when your count differs from the count a manual lists, and it separately names any saw whose manual gives no count for that bar, so you see both notices when both apply. If nothing matches, the result box tells you whether the pitch and gauge are listed only with other bar lengths.
- Read the result box. The table under it shows each listed bar length with its pitch, gauge, drive links and drive sprocket. In “Chain specs” mode, every row has a Source column naming the manual it came from; the US and international STIHL manuals stay on separate rows.
- Before ordering, compare the result with the numbers stamped on your bar or printed on the old chain’s box.
If a drive-link cell shows a dash, the manual does not list a count for that bar. In that case, count the links on your old chain or read the bar stamp; there is no reliable way to work it out from the bar length.
How bar, chain and sprocket fitment works
Fitment is not one number shared by every part. Each spec pairs the chain with a particular component:
- Pitch and chain type must be compatible with the bar nose and the drive sprocket. Pitch is, in Oregon’s words, “the distance between any three consecutive rivets, divided by two”; common pitches are 1/4″, .325″, 3/8″ Low Profile (STIHL calls it 3/8″ P), 3/8″, .404″ and 3/4″. This is why STIHL lists a 6-tooth sprocket for 3/8″ P chain and a 7-tooth sprocket for .325″ chain on the MS 230/MS 250, and pairs its 3/8″ P bars with a 9-tooth nose and its .325″ bars with an 11-tooth nose.
- Gauge must match the bar groove. Gauge is the thickness of the drive links that ride in the groove: .043″, .050″ (1.3 mm), .058″ (1.5 mm) or .063″ (1.6 mm). STIHL states it as the groove width of the bar.
- Drive-link count must be correct for the actual bar and sprocket setup. It sets how long the chain loop is, so it has to suit the specific bar you run on your saw.
For the drive sprocket, Husqvarna lists the type (spur) and tooth count; STIHL lists tooth count and pitch. The bar’s nose sprocket tooth count is shown where the manual gives it.
Drive-link counts cannot be calculated from bar length. The Husqvarna 445/450 manual shows why: it lists one count per bar length, except for the 20-inch bar, where “two different drive link counts exist.”
| Husqvarna 445 / 450 bar | Pitch | Drive links |
|---|---|---|
| 13″ | .325″ | 56 |
| 15″ | .325″ | 64 |
| 16″ | .325″ | 66 |
| 18″ | .325″ | 72 |
| 20″ | .325″ | 78 or 80 |
Bar length is a nominal size, too. Husqvarna notes that “the nominal guide bar size is not necessarily the same as the cutting length,” and STIHL says “the actual cutting length may be less than the specified cutting length.” STIHL lists bars in centimeters; the chart shows the nearest whole inch (cm ÷ 2.54) only so you can search by inches.
STIHL bar, chain and sprocket sizes, plus Echo and Homelite chains
STIHL bar and chain chart: the international manual lists Rollomatic E and E Light bars of 30, 35, 40 and 45 cm in 3/8″ P with a 1.3 mm groove for the MS 210, MS 230 and MS 250, using 63 PM3 or 63 PD3 chain. For the MS 230 and MS 250 it also lists 35, 40 and 45 cm Rollomatic E bars in .325″ with a 1.6 mm groove and 26 RM or 26 RM3 chain. The US MS 250 manual instead lists .325″ bars of 35, 40 and 45 cm with a 1.3 mm gauge and 23 RS, 23 RM or 23 RM3 chain. Because the two manuals disagree on the .325″ gauge, the chart shows both rows separately, each with its own source, rather than merging them.
STIHL sprocket size chart: the MS 210 uses a 6-tooth 3/8″ P sprocket. The MS 230/MS 250 international manual lists 6-tooth and 7-tooth 3/8″ P sprockets and a 7-tooth .325″ sprocket; the US MS 250 manual lists a 7-tooth .325″ sprocket. Bar nose sprockets are 9 teeth on the 3/8″ P bars and 11 teeth on the .325″ international bars.
Echo and Homelite: we could not verify a manufacturer manual for Echo or Homelite saws, so the chart does not list them rather than guess. To size an Echo bar or find a Homelite replacement chain, read the pitch, gauge and drive-link count stamped on the bar’s tail or printed in your owner’s manual, then match all three on the new chain. You can also enter those numbers in the “Chain specs” mode to see which listed saws share them.
Methodology & sources
Each model row was copied from the manufacturer’s operator’s manual named below and checked on October 12, 2026. A model appears only if its manual lists bar, chain and sprocket specs. Drive-link counts are shown only where the manual prints them. Every result names its manual: the model lookup shows it under the table, and the specs lookup gives each matching row its own Source cell. Gauge conversions follow the standard 1.3 mm = .050″, 1.5 mm = .058″ and 1.6 mm = .063″. Cross-brand bar mount codes and aftermarket part numbers are not included because no manufacturer cross-reference was verified.
- Husqvarna 435, 440 operator’s manual
- Husqvarna 445, 450 Rancher operator’s manual
- Husqvarna 455 Rancher, 460 Rancher operator’s manual
- STIHL MS 210, MS 230, MS 250 instruction manual 0458-208-0121-C (international), sections 35.6–35.7
- STIHL MS 250 instruction manual 0458-208-8221 (US)
- Oregon saw chain maintenance manual (pitch definition, pitches and gauges)
Last updated: October 2026
FAQ
Can I work out the drive-link count from the bar length?
No. Drive-link count depends on the bar and sprocket, not just the nominal length; Husqvarna’s 445/450 manual notes that two different drive-link counts (78 and 80) exist for its 20-inch bar. Use the count listed in your manual, count the links on your old chain, or read the bar stamp.
Why does the STIHL MS 250 show two different .325″ gauges?
STIHL’s US manual lists .325″ chain with a 1.3 mm (.050″) gauge for the MS 250, while the international manual lists .325″ with a 1.6 mm (.063″) groove. The chart shows both rows with their source; check the stamp on your own bar.
Why aren’t Echo and Homelite models in the chart?
We only list a model when its bar, chain and sprocket specs come from the manufacturer’s manual, and we could not verify Echo or Homelite manuals. For those saws, read the pitch, gauge and drive-link count stamped on the bar or check your owner’s manual.
Is the bar length the same as the cutting length?
Not necessarily. Husqvarna states that the nominal guide bar size is not necessarily the same as the cutting length, and STIHL says the actual cutting length may be less than the specified length.
What do pitch and gauge mean?
Pitch is the distance between any three consecutive rivets divided by two (Oregon’s definition); the chain’s pitch and type must be compatible with the bar nose and the drive sprocket. Gauge is the thickness of the drive links, and it must match the width of the bar groove they ride in.
Related guides
- Chainsaw Chain Size Chart by Bar Length, Pitch and Saw Model
- How to Measure a Chainsaw Chain: Pitch, Gauge and Drive Links
- How to Count Drive Links on a Chainsaw Chain Without Mistakes
- How Often to Replace a Chainsaw Chain? Signs It’s Worn Out
- How to Dress a Chainsaw Bar: Filing Rails Flat and Removing Burrs
- What Size Chainsaw for an Alaskan Mill? CC and Bar Length Reference
More free tools
Battery Chainsaw Runtime Estimator
Estimate battery chainsaw runtime from battery voltage, amp-hours, rated watts and duty cycle, with an optional corded-saw energy comparison.
Battery vs Gas Chainsaw Cost-of-Ownership Calculator
Compare the total cost of a gas and a battery chainsaw over the years with your own fuel, power and usage numbers, and find the break-even point.
Chainsaw Chain Speed Calculator
Turn RPM, drive sprocket teeth and chain pitch into chain speed in ft/s, m/s, mph or km/h, and compare 7- vs 8-tooth sprockets.
