Skip to content
ChainsawGo logo — chainsaw icon with the ChainsawGo wordmark
  • Home
  • About UsExpand
    • Contact Us
  • Cordless Chainsaws
  • Gas Chainsaws
  • Chainsaw Parts
  • Safety Gear
  • Chains & Bars
  • Free Tools
ChainsawGo logo — chainsaw icon with the ChainsawGo wordmark
Free calculator

Pole Saw Reach Calculator

Check whether your pole saw reaches a branch, or find the pole length you need, from your reach, the branch height and your working angle.

  • Free
  • No sign-up
  • Runs in your browser
Estimates only · data checked October 2026 · About this data

This calculator is an estimate for planning only and is not safety advice. Pole saws can cause serious injury, and falling branches and contact with power lines can be fatal. Never work near power lines, wear appropriate protective equipment, follow your saw's manual, and hire a qualified arborist for large, high or hazardous limbs.

Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.

Quick answer

To pick what size pole saw you need to trim a branch, subtract your standing reach from the height of the cut point and divide by the sine of your working angle. Enter your numbers below to check whether your saw reaches, or to find the pole length you need.

How to use the Pole Saw Reach Calculator

  1. Choose a mode. A. Will my pole saw reach? checks a saw you already have. B. How long a pole do I need? works out the length the geometry requires.
  2. Pick Imperial (feet) or Metric (metres). Switching converts the values you have typed without changing any measurement or result.
  3. Enter the branch height to the cut point and your standing reach (the height of your upper grip hand while working).
  4. Enter the working angle of the pole above horizontal, measured at your upper grip, from 10° to 90°. Use the number box or the slider.
  5. In mode A, enter the pole length from your upper grip to the cutting point, with the saw extended as you will use it. The measuring section below explains how to get this figure.
  6. Press Calculate. The result shows the headline number, the horizontal distance to the cut point and the formulas with your numbers filled in, so you can check them.

Decimal commas work too: “2,5” is read as 2.5. The input limits (60 ft / 18.288 m branch height, 9 ft / 2.7432 m standing reach, 30 ft / 9.144 m pole length) only catch typos. They are not recommendations or product claims. The metric limits are the imperial limits converted exactly, so a measurement accepted in one unit is still accepted after you switch.

How the calculation works

The pole, the vertical line from your hands and the ground line form a right triangle. The pole is the hypotenuse, so the height it adds above your hands is its length times the sine of the angle. The horizontal distance to the cut point is its length times the cosine.

Pole saw reach right-triangle diagram The upper grip sits a height R above the ground. The pole runs from the upper grip to the cutting point, and its length along the pole is L. The working angle θ is measured at the upper grip, between the horizontal and the pole. The horizontal side of the triangle is D, equal to L times cos θ, and the vertical side is L times sin θ. The cut point is a height H above the ground, so H equals R plus L times sin θ. Ground R upper grip L D L × sin θ θ cut point H
θ is measured at your upper grip, between the horizontal and the pole. L runs along the pole from that grip to the cutting point. D is the horizontal distance to the cut point, and H = R + L × sin θ.
  • H: height of the cut point above the ground.
  • R: standing reach, the height of your upper grip above the ground while working.
  • L: length from your upper grip to the cutting point, measured along the pole. This is not necessarily the saw’s total length.
  • θ: working angle of the pole above horizontal, measured at your upper grip (90° = vertical).
  • D: horizontal distance from your upper grip to the point directly below the cut point.
  • Working height (mode A): H_max = R + L × sin(θ). The saw reaches if H_max ≥ H; otherwise it is short by H − H_max.
  • Required length (mode B): L_req = (H − R) ÷ sin(θ). If H ≤ R the result is clamped at zero, L_req = max(0, (H − R) ÷ sin(θ)), and D is 0.
  • Horizontal offset: D = L × cos(θ) (mode A) or D = L_req × cos(θ) (mode B).
Standing reach RBranch height HAngle θsin(θ)Required length L_req
2590°1(5 − 2) ÷ 1 = 3
2530°0.5(5 − 2) ÷ 0.5 = 6
Worked examples in the same unit (feet or metres). Lowering the angle from 90° to 30° doubles the length needed.

The reverse check works the same way: with R = 2, L = 4 and θ = 30°, the working height is 2 + 4 × 0.5 = 4, so a cut point at 5 would be out of reach by 1.

Measuring your reach, and why listed reach is not your reach

Measure standing reach and branch height

Stand on the ground where you will work, raise your arm to the position your upper hand holds the pole, and have someone measure from the ground to your hand with a tape. For the branch, measure to the point where you plan to cut, not to the branch tip. If you can’t reach it with a tape, compare it with something of known height nearby, such as a wall or fence you have already measured.

Measure the grip-to-cutting-point length

The calculator needs L, the distance along the pole from where your upper hand grips it to the cutting point. Check how your saw’s spec sheet or manual measures its extended length. If it is measured between those same two points, you can use it as it is. If not, extend the saw to the length you will work at, hold it where you normally grip it, and measure from that grip position to the cutting point with a tape. Any part of the tool below your upper grip adds nothing to your height.

The angle effect

A pole adds its full length to your height only when it points straight up. At any lower angle it adds L × sin(θ), which is less. A manufacturer’s maximum-reach figure is set under the manufacturer’s own assumptions, so treat it as their claim and use this calculator to check your own working height. Mode B gives a grip-to-cutting-point length, so compare it with the same measurement on a saw, not with its total length or advertised reach. This page does not state lengths, extension counts or compatibility for any brand.

Stay clear of the drop zone

Don’t stand under the branch you are cutting. It can fall toward you. A cut branch can land anywhere near and below the cut point, and it may swing or bounce. Pick a position to the side, then re-check the angle in the calculator, because moving changes your angle and therefore your reach. Steep angles close to 90° put the saw almost directly overhead, which puts you in the drop zone.

Methodology & sources

All inputs are converted to metres internally using exact factors (1 ft = 0.3048 m, 1 in = 0.0254 m). The angle is converted to radians (θ × π ÷ 180), and the formulas above are applied. Results are converted back to your chosen unit and rounded to one decimal for display only. Intermediate and stored values are never rounded. Switching units keeps each value as you typed it, in its original unit, so it never changes a measurement or a verdict. Input limits are checked in metres against the same physical limits in both unit systems. If a shortfall is smaller than the display precision, it is shown as “less than 0.1”. When the cut point is at or below your standing reach, the required length is clamped at zero; that is a height-only result, not a claim that a tool of zero length can make the cut. Nothing you type is stored or sent anywhere.

Assumptions: a straight pole with no flex, flat ground, a cut point measured vertically, and L measured from the upper grip to the cutting point. The tool does not model pole flex, uneven or sloping ground, tilted branches, your body position, the length of the saw head beyond the cutting point, or any product’s real-world reach.

  • Inch (Wikipedia): exact definition, 1 in = 25.4 mm and 1/12 ft, so 1 ft = 0.3048 m.
  • Trigonometric functions (Wikipedia): standard sine and cosine definitions used in the formulas.
  • Your saw’s manufacturer spec sheet or manual: shows how its extended length is measured. Use that figure only if it runs from your upper grip to the cutting point; otherwise measure that segment yourself. We don’t copy or quote it.

Last updated: October 2026

This calculator is an estimate for planning only and is not safety advice. Pole saws can cause serious injury, and falling branches and contact with power lines can be fatal. Never work near power lines, wear appropriate protective equipment, follow your saw’s manual, and hire a qualified arborist for large, high or hazardous limbs.

FAQ

What size pole saw do I need to trim a branch?

Subtract your standing reach from the height of the cut point, then divide by the sine of your working angle: L = (H − R) ÷ sin(θ). The calculator does this for you and shows the substituted formula.

How long are pole saws?

Lengths vary by model, so check your own saw’s manual or spec sheet. For this calculator, enter the distance from your upper grip to the cutting point: use the listed total extended length only if it is measured between those same two points; otherwise extend the saw and measure that segment yourself.

How many extensions can I add to my pole saw?

Only the manufacturer can answer that for a specific model, so follow your saw’s manual and spec sheet. This calculator does not state extension counts or compatibility for any brand.

Why does my pole saw reach less than its advertised reach?

A pole held at an angle gains only L × sin(θ) of height, which is less than its full length unless it is vertical. Advertised reach figures are also set by the manufacturer under their own assumptions.

Do I need a long pole saw for high trees?

Use the calculator with your branch height and a realistic working angle to see the length the geometry requires. If the result is very long or the limb is large, high or near power lines, hire a qualified arborist.

Related guides

  • Chainsaw Chain Size Chart by Bar Length, Pitch and Saw Model

More free tools

Battery Chainsaw Runtime Estimator

Estimate battery chainsaw runtime from battery voltage, amp-hours, rated watts and duty cycle, with an optional corded-saw energy comparison.

Battery vs Gas Chainsaw Cost-of-Ownership Calculator

Compare the total cost of a gas and a battery chainsaw over the years with your own fuel, power and usage numbers, and find the break-even point.

Chainsaw Bar, Chain & Sprocket Fitment Chart

Look up bar lengths, chain pitch, gauge, drive links and sprocket for listed Husqvarna and STIHL saws, or find saws by pitch and gauge.

See all free tools (9) →

  • Home
  • About Us
  • Contact Us
  • HTML SITEMAP
  • Privacy Policy
  • Terms of Service
  • Affiliate Disclaimer
  • How We Research

Please keep in mind that we may receive commissions when you click our links and make purchases. However, this does not sway our reviews and comparisons. We try our best to keep things unbiased, in order to help you make the best choice. As Amazon Associate, we earn from qualifying purchases.

© 2026 ChainsawGo | All Rights Reserved.

Scroll to top
  • Home
  • About Us
    • Contact Us
  • Cordless Chainsaws
  • Gas Chainsaws
  • Chainsaw Parts
  • Safety Gear
  • Chains & Bars
  • Free Tools
Search